Heat-glo-fireplace HEAT&GLO ST-36TRB-IPI Manual de usuario Pagina 10
- Pagina / 82
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/1310
D. Clear Space
WARNING! DO NOT place combustible objects in front
of the fi replace or block louvers. High temperatures may
start a fi re. See Figure 2.4.
Avoid placing candles and other heat-sensitive objects on
mantel or hearth. Heat may damage these objects.
Figure 2.4 Clear Space
F. Fixed Glass Assembly
See Section 14.G.
E. Decorative Doors and Fronts
WARNING! Risk of Fire! Install ONLY doors or fronts
approved by Hearth & Home Technologies. Unapproved
doors or fronts may cause fi replace to overheat.
This fireplace has been supplied with an integral
barrier to prevent direct contact with the fi xed glass
panel. DO NOT operate the fi replace with the barrier
removed.
Contact your dealer or Hearth & Home Technologies if
the barrier is not present or help is needed to properly
install one.
For more information refer to the instructions supplied with
your decorative door or front.
G. Remote Controls, Wall Controls and Wall
Switches
Follow the instructions supplied with the control installed
to operate your fi replace:
For safety:
• Install a switch lock or a wall/remote control with child
protection lockout feature.
• Keep remote controls out of reach of children.
See your dealer if you have questions.
CLEAR SPACE
3 FT. IN FRONT OF FIREPLACE
H. Before Lighting Fireplace
Before operating this fi replace for the fi rst time, have a
qualifi ed service technician:
• Verify all shipping materials have been removed from
inside and/or underneath the fi rebox.
• Review proper placement of logs, ember material and/or
other decorative materials.
• Check the wiring.
• Check the air shutter adjustment.
• Ensure that there are no gas leaks.
• Ensure that the glass is sealed and in the proper position
and that the integral barrier is in place.
WARNING! Risk of Fire or Asphyxiation! DO NOT op-
erate fi replace with fi xed glass assembly removed.
THREADED STUD USED TO
INSTALL TEMPERATURE SENSOR
FAN
Figure 2.2 Blower Location
RHEOSTAT ATTACHMENT TAB
Figure 2.3 Rheostat Attachment Tab Location
C. Blower Kit (optional)
If desired, a blower kit may be added. Contact your deal-
er to order the correct fan kit.
Blower Installation
1. Install and wire the blower in appliance as shown in
Figure 2.2.
2. Wire the blower temperature sensor and adjustable
speed control (rheostat) according to the instructions
provided with the fan.
3. If rheostat is required, bend rheostat attachment tab
located in bottom of fi replace upward as shown in
Figure 2.3.
4. Attach rheostat to the rheostat attachment tab.
- Owner’s Manual 1
- A. Congratulations 2
- Table of Contents 3
- User Guide 3
- B. Limited Lifetime Warranty 5
- LIMITED LIFETIME WARRANTY 5
- WARRANTY CONDITIONS: 6
- This warranty is void if: 6
- LIMITATIONS OF LIABILITY: 6
- WARRANTY EXCLUSIONS: 6
- Listing and Code Approvals 7
- Massachusetts 8
- Figure 2.4 Clear Space 10
- Figure 2.2 Blower Location 10
- CAUTION: 11
- WARNING: 11
- J. After Fireplace is Lit 12
- K. Frequently Asked Questions 12
- Maintenance and Service 13
- Burner Ignition and Operation 15
- Installer Guide 16
- C. Tools and Supplies Needed 17
- Framing and Clearances 18
- C. Clearances 19
- MEASUREMENTS FROM 21
- TOP EDGE OF THE OPENING 21
- Termination Locations 23
- Electrical 24
- Service 24
- A. Approved Pipe 25
- C. Use of Elbows 25
- B. Vent Table Key 25
- D. Measuring Standards 25
- E. Vent Diagrams 26
- One Elbow 27
- Two Elbows 27
- Three Elbows 28
- Figure 7.7 29
- Figure 7.8 29
- 1 2 3 4 5 30
- SETTINGS 30
- No Elbow 32
- One 45° Elbow 32
- = 16 in. (406 mm) Maximum 32
- Materials 36
- Figure 8.2 36
- C. Wall Penetration Framing 37
- Figure 8.6 38
- Appliance Preparation 40
- B. Rear Vent 41
- NAILING TABS 42
- SIDE TO SIDE 42
- FRONT TO BACK 42
- Figure 10.2 43
- Figure 10.3 43
- Figure 10.4 Seams 43
- C. Assemble Slip Sections 44
- E. Disassemble Vent Sections 45
- D. Secure the Vent Sections 45
- (SLP only) 46
- Termination 48
- Cap Specifi cation Chart 49
- Gas Information 50
- Electrical Information 51
- E. Junction Box Installation 53
- Finishing 54
- C. Facing Material 57
- D. Finishing Material 57
- 33-3/4 in 58
- 37-1/4 in 58
- E. Elevated Hearth Systems 59
- Appliance Setup 60
- Log Set Assembly: LOGS-2128 61
- I. Air Shutter Setting 63
- G. Fixed Glass Assembly 63
- Troubleshooting 64
- Reference Materials 66
- B. Vent Components Diagrams 69
- DVP-HRC-SS 73
- Effective Height/Length 74
- LCOR-36TRB-IPI 76
- PIER-36TRB-IPI 77
- RCOR-36TRB-IPI 78
- ST-36TRB-IPI 79
- Service Parts 80
- #15 Valve Assembly 80
- DO NOT DISCARD THIS MANUAL 82
Relacionado con productos y manuales para Horno Heat-glo-fireplace HEAT&GLO ST-36TRB-IPI
Horno Heat-glo-fireplace CERONA-36 Manual de usuario
(65 paginas)
(65 paginas)
Horno Heat-glo-fireplace LUX60 Manual de usuario
(60 paginas)
(60 paginas)
Horno Heat-glo-fireplace BAY-40 Manual de usuario
(52 paginas)
(52 paginas)
Horno Heat-glo-fireplace Heat&Glo DirectVent Gas Fireplace 6000 Series Manual de usuario
(8 paginas)
(8 paginas)
Horno Heat-glo-fireplace 8000TVD Manual de usuario
(20 paginas)
(20 paginas)
(26 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.213 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales