Heat-glo-fireplace HEAT&GLO ST-36TRB-IPI Manual de usuario Pagina 36
- Pagina / 82
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. i • 3/1336
A. Pipe Clearances to Combustibles
WARNING! Risk of Fire! Maintain air space clearance to
vent. DO NOT pack insulation or other combustibles:
• Between ceiling fi restops
• Between wall shield fi restops
• Around vent system
Failure to keep insulation or other material away from
vent pipe may cause over heating and fi re.
8
8
Vent Clearances and Framing
Figure 8.1 Horizontal Venting Clearances To Combustible
Materials
* When using SLP pipe, minimum clearances from the vent pipe to combustible materi-
als at wall shield firestops are: Top: 2-1/2 in. (64 mm)
Bottom: 1/2 in. (13 mm)
Sides: 1 in. (25 mm)
Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm).
DVP heat shield - designed to be used on a wall 4 in. to 7-1/4 in. (102 mm to 184
mm) thick.
,f wall thickness is less than 4 in. the e[isting heat shields must be field trimmed. ,f
wall thickness is greater than 7-1/4 in. a DVP-HSM-B will be required.
SLP heat shield - designed to be used on a wall 4-3/8 in. to 7-5/8 in. (111 mm to
194 mm thick).
,f wall thickness is less than 4-3/8 the e[isting heat shields must be field trimmed.
,f wall thickness is greater than 7-5/8 in. a DVP-HSM-B will be required.
(DVP-SLP Pipe Shown)
3 in. (76 mm)
top clearance *
1 in. (25 mm)
clearance
bottom & sides
Heat
Shield
Wall
Shield
Firestop
Heat
Shield
WALL
3 in. (76 mm)
top clearance *
1 in. (25 mm)
clearance
bottom & sides
Heat
Shield
Wall
Shield
Firestop
Heat
Shield
WALL
3 in. (76 mm)
top clearance
1 in. (25 mm)
clearance around
vertical sections
B. Continue Adding Vent Components
WARNING! Risk of Fire! Installation of this appliance
may require the use of heat shield 385-920 above the
fi rst 90
0
elbow in the venting system.
• The heat shield is required above the fi rst elbow if the
clearance to combustible surface above is between
three (3) and four (4) inches. A shield is not required for
clearances greater than four inches. See Figure 8.2.
• Fasten the shield in place using the four pilot holes
provided in the part. The shield should be oriented such
that the 13-1/8 inch dimension (longest dimension) is
running in the same direction the elbow is pointing. The
shield should be centered directly above the elbow, and
positioned so that it creates a 1/2 inch airspace between
the shield and the combustible surface. See Figure 8.3.
Figure 8.2
HEAT
SHIELD
3 in. MIN.
(76 mm)
COMBUSTIBLE
SURFACE
(Required for clearances
between 3 and 4 inches.)
- Owner’s Manual 1
- A. Congratulations 2
- Table of Contents 3
- User Guide 3
- B. Limited Lifetime Warranty 5
- LIMITED LIFETIME WARRANTY 5
- WARRANTY CONDITIONS: 6
- This warranty is void if: 6
- LIMITATIONS OF LIABILITY: 6
- WARRANTY EXCLUSIONS: 6
- Listing and Code Approvals 7
- Massachusetts 8
- Figure 2.4 Clear Space 10
- Figure 2.2 Blower Location 10
- CAUTION: 11
- WARNING: 11
- J. After Fireplace is Lit 12
- K. Frequently Asked Questions 12
- Maintenance and Service 13
- Burner Ignition and Operation 15
- Installer Guide 16
- C. Tools and Supplies Needed 17
- Framing and Clearances 18
- C. Clearances 19
- MEASUREMENTS FROM 21
- TOP EDGE OF THE OPENING 21
- Termination Locations 23
- Electrical 24
- Service 24
- A. Approved Pipe 25
- C. Use of Elbows 25
- B. Vent Table Key 25
- D. Measuring Standards 25
- E. Vent Diagrams 26
- One Elbow 27
- Two Elbows 27
- Three Elbows 28
- Figure 7.7 29
- Figure 7.8 29
- 1 2 3 4 5 30
- SETTINGS 30
- No Elbow 32
- One 45° Elbow 32
- = 16 in. (406 mm) Maximum 32
- Materials 36
- Figure 8.2 36
- C. Wall Penetration Framing 37
- Figure 8.6 38
- Appliance Preparation 40
- B. Rear Vent 41
- NAILING TABS 42
- SIDE TO SIDE 42
- FRONT TO BACK 42
- Figure 10.2 43
- Figure 10.3 43
- Figure 10.4 Seams 43
- C. Assemble Slip Sections 44
- E. Disassemble Vent Sections 45
- D. Secure the Vent Sections 45
- (SLP only) 46
- Termination 48
- Cap Specifi cation Chart 49
- Gas Information 50
- Electrical Information 51
- E. Junction Box Installation 53
- Finishing 54
- C. Facing Material 57
- D. Finishing Material 57
- 33-3/4 in 58
- 37-1/4 in 58
- E. Elevated Hearth Systems 59
- Appliance Setup 60
- Log Set Assembly: LOGS-2128 61
- I. Air Shutter Setting 63
- G. Fixed Glass Assembly 63
- Troubleshooting 64
- Reference Materials 66
- B. Vent Components Diagrams 69
- DVP-HRC-SS 73
- Effective Height/Length 74
- LCOR-36TRB-IPI 76
- PIER-36TRB-IPI 77
- RCOR-36TRB-IPI 78
- ST-36TRB-IPI 79
- Service Parts 80
- #15 Valve Assembly 80
- DO NOT DISCARD THIS MANUAL 82
Relacionado con productos y manuales para Horno Heat-glo-fireplace HEAT&GLO ST-36TRB-IPI
Horno Heat-glo-fireplace CERONA-36 Manual de usuario
(65 paginas)
(65 paginas)
Horno Heat-glo-fireplace LUX60 Manual de usuario
(60 paginas)
(60 paginas)
Horno Heat-glo-fireplace BAY-40 Manual de usuario
(52 paginas)
(52 paginas)
Horno Heat-glo-fireplace Heat&Glo DirectVent Gas Fireplace 6000 Series Manual de usuario
(8 paginas)
(8 paginas)
Horno Heat-glo-fireplace 8000TVD Manual de usuario
(20 paginas)
(20 paginas)
(26 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.361 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales